Standards for Low voltage Industrial Products
to be used for OY-ELSPECTA-AB Certification
Updated: November 2020
| IEC | EN or HD | EQUIPMENT | |
|---|---|---|---|
| EN 50085 | CABLE TRUNKING SYSTEMS AND CABLE DUCTING SYSTEMS FOR ELECTRICAL INSTALLATIONS | ||
| EN 50085-1 | Part 1: General requirements | ||
| IEC 60044 | INSTRUMENT TRANSFORMERS | ||
| IEC 60044-7 | EN 60044-7 | Part 7: Electronic voltage transformers | |
| IEC 60076 | POWER TRANSFOMERS | ||
| IEC 60076-1 | EN 60076-1 | Power transformers - Part 1: General | |
| IEC 60076-2 | EN 60076-2 | Part 2: Temperature rise for liquid-immersed transformers | |
| IEC 60076-3 | EN 60076-3 | Part 3: Insulation levels, dielectric tests and external clearances in air | |
| IEC 60076-5 | EN 60076-5 | Part 5: Ability to withstand short circuit | |
| IEC 60076-6 | EN 60076-6 | Part 6: Reactors | |
| IEC 60076-11 | EN 60076-11 | Part 11: Dry-type transformers | |
| IEC 60076-13 | EN 60076-13 | Part 13: Self-protected liquid-filled transformers | |
| IEC 60076-14 | EN 60076-14 | Part 14: Liquid-immersed power transformers using high-temperature insulation materials | |
|
IEC 60076-18 IEC 60079-0 IEC 60079-1 IEC 60079-2 IEC 60079-5 IEC 60079-6 IEC 60079-7 IEC 60079-10 IEC 60079-11 |
EN 60076-18 EN 60079-0 EN 60079-1 EN 60079-2 EN 60079-5 EN 60079-6 EN 60079-7 EN 60079-10 EN 60079-11 |
Part 18: Measurement of frequency response Part 0: Explosive atmospheres - Part 0: Equipment - General requirements Part 1: Explosive atmospheres - Equipment protection by flameproof enclosures "d" Part 2: Explosive atmospheres - Equipment protection by pressurized enclosure "p" Part 5: Explosive atmospheres - Equipment protection by powder filling "q" Part 6: Explosive atmospheres - Equipment protection by liquid immersion "o" Part 7: Explosive atmospheres - Equipment protection by increased safety "e" Part 10-1: Explosive atmospheres - Classification of areas - Explosive gas atmospheres Part 11: Explosive atmospheres - Equipment protection by intrinsic safety "i" |
|
| IEC 61378-1 *) | EN 61378-1 *) | Converter transformers - Part 1: Transformers for industrial applications | |
| EN 50464-1 *) | Three-phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2 500 kVA with highest voltage for equipment not exceeding 36 kV – Part 1: General requirements | ||
| EN 50464-3 *) | Three-phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2 500 kVA with highest voltage for equipment not exceeding 36 kV – Part 3: Determination of the power rating of a transformer loaded with non-sinusoidal currents | ||
| EN 50464-4 *) | Three-phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2 500 kVA with highest voltage for equipment not exceeding 36 kV – Part 4: Requirements and tests concerning pressurised corrugated tanks. | ||
| EN 50541-1 *) | Three phase dry-type distribution transformers 50 Hz, from 100 kVA to 3150 kVA, with highest voltage for equipment not exceeding 36 kV – Part 1: General requirements | ||
| EN 50588-1 *) | Medium power transformers 50 Hz, with highest voltage for equipment not exceeding 36 kV - Part 1: General requirements | ||
| Remark: *) Although these standards exceed the low voltage area, they are included in the scope of LOVAG, because they may be applicable for products under the LOVAG agreement. | |||
| IEC 60252 | AC MOTOR CAPACITORS | ||
| IEC 60252-1 | EN 60252-1 | Part 1: General - Performance, testing and rating - Safety requirements - Guidance for installation and operation | |
| IEC 60252-2 | EN 60252-2 | Part 2: Motor start capacitors | |
| IEC 60266 | EN 60255 | ELECTRICAL RELAYS | |
| IEC 60255-12 | - | Part 12: Directional relays and power relays with two input energizing quantities | |
| IEC 60255-13 | - | Part 13: Biased (percentage) differential relays | |
| IEC 60269 | EN 60269 | LOW VOLTAGE FUSES | |
| IEC 60269-1 | EN 60269-1 | Part 1: General requirements | |
| IEC 60269-2 | EN 60269-2 | Part 2: Supplementary requirements for fuses for use by authorized persons | |
| IEC 60269-3 | EN 60269-3 | Part 3: Supplementary requirements for fuses for use by unskilled persons for fuses for use by unskilled persons | |
| IEC 60269-4 | EN 60269-4 | Part 4: Supplementary requirements for fuse-links for the protection of semiconductor devices | |
| IEC 60309 | EN60309 | PLUGS, SOCKET-OUTLETS COUPLERS FOR INDUSTRIAL PURPOSES | |
| IEC 60309-1 | EN 60309-1 | Part 1: General requirements | |
| IEC 60309-2 | EN 60309-2 | Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories | |
| IEC 60439 IEC 61439 | EN 61439 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES | |
| IEC 61439-1 | EN 61439-1 | Part 1: General rules | |
| IEC 61439-2 | EN 61439-2 | Part 2: Power switchgear and controlgear assemblies | |
| IEC 61439-3 | EN 61439-3 | Part 3: Part 3: Distribution boards intended to be operated by ordinary persons (DBO) | |
| IEC 61439-4 | EN 61439-4 | Part 4: Particular requirements for assemblies for construction sites (ACS) | |
| IEC 61439-5 | EN 61439-5 | Part 5: Assemblies for power distribution in public networks | |
| IEC 61439-6 | EN 61439-6 | Part 6: Busbar trunking systems (busways) | |
| IEC 61439-7 | EN 61439-7 | Part 7: Assemblies for specific installations such as marinas, camping sites, market squares, electrical vehicles charging stations | |
| IEC/TR 61641 | Enclosed low-voltage switchgear and controlgear assemblies - Guide for testing under conditions of arcing due to internal fault | ||
| IEC 60831 | SHUNT POWER CAPACITORS OF THE SELF-HEALING TYPE FOR A.C. SYSTEMS HAVING A RATED VOLTAGE UP TO AND INCLUDING 1 000 V | ||
| IEC 60831-1 | EN 60831-1 | Part 1: General - Performance, testing and rating - Safety requirements - Guide for installation and operation | |
| IEC 60831-2 | EN 60831-2 | Part 2: Ageing test, self-healing test and destruction test | |
| IEC 61869 | INSTRUMENT TRANSFORMERS | ||
| IEC 61869-1 | EN 61869-1 | Part 1: General requirements | |
| IEC 61869-2 | EN 61869-2 | Part 2: Additional requirements for current transformers | |
| IEC 61869-3 | EN 61869-3 | Part 3: Additional requirements for inductive voltage transformers | |
| IEC 61869-4 | EN 61869-4 | Part 4: Additional requirements for combined transformers | |
| IEC 60931 | SHUNT POWER CAPACITORS OF THE NON-SELF-HEALING TYPE FOR A.C. SYSTEMS HAVING A RATED VOLTAGE UP TO AND INCLUDING 1000 V | ||
| IEC 60931-1 | EN 60931-1 | Part 1: General - Performance, testing and rating - Safety requirements - Guide for installation and operation | |
| IEC 60931-2 | EN 60931-2 | Part 2: Ageing test and destruction test | |
| IEC 60931-3 | EN 60931-3 | Part 3: Internal fuses | |
| IEC TR 60996 | - | Method for verifying accuracy of tan delta measurements applicable to capacitors | |
| IEC 60947 | EN 60947 | LOW VOLTAGE SWITCHGEAR AND CONTROLGEAR | |
| IEC 60947-1 | EN 60947-1 | Part 1: General rules | |
| IEC 60947-2 | EN 60947-2 | Part 2: Circuit breakers | |
| IEC 60947-3 | EN 60947-3 | Part 3: Switches, disconnectors, switch-disconnectors and fuse combination units | |
| Part 4: Contactors and motor starters | |||
| IEC 60947-4-1 | EN 60947-4-1 | Sect. 1: Electrotechnical contactors and motor starters | |
| IEC 60947-4-2 | EN 60947-4-2 | Sect. 2: AC semicontactor motor controllers and starters | |
| IEC 60947-4-3 | EN 60947-4-3 | Sect. 3: AC semicontactor controllers and contactors for non-motor loads | |
| Part 5: Control circuit devices and switching elements | |||
| IEC 60947-5-1 | EN 60947-5-1 | Sect. 1: Electromechanical control circuit devices | |
| IEC 60947-5-2 | EN 60947-5-2 | Sect. 2: Proximity switches | |
| IEC 60947-5-5 | EN 60947-5-5 | Sect. 5: Electrical emergency stop devices with mechanical latching function | |
| IEC 60947-5-6 | EN 60947-5-6 | Sect. 6: DC interface for proximity sensors and switching amplifiers (NAMUR) | |
| IEC 60947-5-8 | EN 60947-5-8 | Sect. 8: Enabling control devices | |
| IEC 60947-5-9 | EN 60947-5-9 | Sect. 9: Flow rate switches | |
| Part 6: Multiple function equipment | |||
| IEC 60947-6-1 | EN 60947-6-1 | Sect. 1: Automatic transfer switching equipment | |
| IEC 60947-6-2 | EN 60947-6-2 | Sect. 2: Control and protective switching devices (CPS) | |
| Part 7: Ancillary Equipment | |||
| IEC 60947-7-1 | EN 60947-7-1 | Sect. 1: Terminal blocks for copper conductors | |
| IEC 60947-7-2 | EN 60947-7-2 | Sect. 2: Protective conductor terminal blocks for copper conductors | |
| IEC 60947-7-3 | EN 60947-7-3 | Sect. 3: Ancillary equipment - Safety requirements for fuse terminal blocks | |
| IEC 60947-7-4 | EN 60947-7-4 | Sect. 4: Ancillary equipment – PCB terminal blocks for copper conductors | |
| IEC 60947-8 | EN 60947-8 | Part 8: Control units for built-in thermal protection (PTC) for rotating electrical machines | |
| IEC 61131 | EN 61131 | PROGRAMMABLE CONTROLLERS | |
| IEC 61131-1 | EN 61131-1 | Part 1: General information | |
| IEC 61131-2 | EN 61131-2 | Part 2: Equipment requirements | |
| IEC 61386 | EN 61386 | CONDUIT SYSTEMS FOR CABLE MANAGEMENT | |
| IEC 61386-1 | EN 61386-1 | Part 1: General requirements | |
| IEC 61386-21 | EN 61386-21 | Part 21: Particular requirements - Rigid conduit systems | |
| IEC 61386-22 | EN 61386-22 | Part 22: Particular requirements - Pliable conduit systems | |
| IEC 61386-23 | EN 61386-23 | Part 23: Particular requirements - Flexible conduit systems | |
| IEC 61386-24 | EN 61386-24 | Part 24: Particular requirement - Conduit systems buried underground | |
| IEC 61558 | EN 61558 | SAFETY OF TRANSFORMERS POWER SUPPLY UNITS AND SIMILAR | |
| IEC 61558-1 | EN 61558-1 | Part 1: General requirements and tests | |
| IEC 61558-2-1 | EN 61558-2-1 | Part 2-1: Particular requirements for separating transformers for general use | |
| IEC 61558-2-2 | EN 61558-2-2 | Part 2-2: Particular requirements and tests for control transformers and power supplies incorporating control transformers | |
| IEC 61558-2-3 | EN 61558-2-3 | Part 2-3: Particular requirements and tests for ignition transformers for gas and oil burners | |
| IEC 61558-2-4 | EN 61558-2-4 | Part 2-4: Particular requirements for isolating transformers for general use | |
| IEC 61558-2-5 | EN 61558-2-5 | Part 2-5: Particular requirements and test for transformer for shavers, power supply units for shavers and shaver supply units | |
| IEC 61558-2-6 | EN 61558-2-6 | Part 2-6: Particular requirements and tests for safety isolating transformers and power supply units incorporating safety isolating transformers | |
| IEC 61558-2-7 | EN 61558-2-7 *) | Part 2-7: Particular requirements and tests for transformers and power supplies for toys *) EN modified | |
| IEC 61558-2-8 | EN 61558-2-8 | Part 2-8: Particular requirements and tests for transformers and power supply units for bells and chimes | |
| IEC 61558-2-9 | EN 61558-2-9 | Part 2-9: Particular requirements and tests for transformers and power supply units for class III handlamps for tungsten filament lamps | |
| IEC 61558-2-10 | EN 61558-2-10 | Part 2-10: Particular requirements and tests for separating transformers with high insulation level and separating transformers with output voltages exceeding 1 000 V | |
| IEC 61558-2-12 | EN 61558-2-12 | Part 2-12: Particular requirements and tests for constant voltage transformers and power supply units for constant voltage | |
| IEC 61558-2-13 | EN 61558-2-13 | Part 2-13: Particular requirements and tests for auto transformers and power supply units incorporating auto transformers | |
| IEC 61558-2-14 | EN 61558-2-14 | Part 2-14: Particular requirements and tests for variable transformers and power supply units incorporating variable transformers | |
| IEC 61558-2-15 | EN 61558-2-15 | Part 2-15: Particular requirements and tests for isolating transformers for the supply of medical locations | |
| IEC 61558-2-16 | EN 61558-2-16 | Part 2-16: Particular requirements and tests for switch mode power supply units and transformers for switch mode power supply units | |
| IEC 61558-2-20 | EN 61558-2-20 | Part 2-20: Particular requirements and tests for small reactors | |
| IEC 61558-2-23 | EN 61558-2-23 | Part 2-23: Particular requirements and tests for transformers and power supply units for construction sites | |
| IEC 61558-2-26 | EN 61558-2-26 | Part 2-26: particular requirements and tests for transformers and power supply units all for saving energy and other purposes | |
| IEC 61642 | INDUSTRIAL A.C. NETWORKS AFFECTED BY HARMONICS - APPLICATION OF FILTERS AND SHUNT CAPACITORS | ||
| IEC 61643 | LOW-VOLTAGE SURGE PROTECTIVE DEVICES | ||
| IEC 61643-11 | EN 61643-11 **) | Part 11: Surge protective devices connected to low-voltage power systems - Requirements and test methods *) EN modified | |
| IEC 61643-12 | - | Part 12: Surge protective devices connected to low-voltage power distribution systems - Selection and application principles | |
| IEC 61643-21 | EN 61643-21 **) | Part 21: Surge protective devices connected to telecommunications and signaling networks - Performance requirements and testing methods **) EN modified | |
| IEC 61812 | EN 61812 | SPECIFIED TIME RELAYS FOR INDUSTRIAL USE | |
| IEC 61812-1 | EN 61812-1 | Part 1: Requirements and tests | |
| IEC 61851 | EN 61851 | ELECTRIC VEHICLE CONDUCTIVE CHARGING SYSTEM | |
| IEC 61851-1 | EN 61851-1 | Part 1: General requirements | |
| IEC 61851-23 | EN 61851-23 | Part 23: DC electric vehicle charging station | |
| IEC 62196-1 | EN 62196-1 | Part 1: General requirements | |
| IEC 62196-2 | EN 62196-2 | Part 2: Dimensional compatibility and interchangeability requirements for a.c. pin and contact-tube accessories | |
| IEC 61921 | POWER CAPACITORS - LOW-VOLTAGE POWER FACTOR CORRECTION BANKS | ||
| IEC 62208 | EN 62208 | EMPTY ENCLOSURES FOR LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES | |
| IEC 62208 | EN 62208 | General requirements | |
| IEC 60240 | UNINTERRUPTIBLE POWER SYSTEMS (UPS) | ||
| IEC 62040-1 | EN 62040-1 | Part 1: General and safety requirements for UPS | |
| IEC 62040-2 | - | Part 2: Electromagnetic compatibility (EMC) requirements | |
| IEC 62041 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND COMBINATIONS THEREOF - EMC REQUIREMENTS | ||
Horizontal standards to be used for OY-ELSPECTA-AB
| Number of Standard | ||
|---|---|---|
| IEC | EN or HD | EQUIPMENT |
| IEC 60068 | EN 60068 | ENVIRONMENTAL TESTING - Part 2: Tests |
| IEC 60068-2-6 | EN 60068-2-6 | Test Fc: Vibration (sinusoidal) |
| IEC 60068-2-11 | EN 60068-2-11 | Test Ka Salt mist |
| IEC 60068-2-20 | Test T: Soldering | |
| IEC 60068-2-27 | EN 60068-2-27 | Test Ea and guidance: Shock |
| IEC 60068-2-30 | EN 60068-2-30 | Test Db and guidance: Damp heat, cyclic (12 + 12 hour cycle) |
| IEC 60529 | EN 60529 | DEGREES OF PROTECTION PROVIDED BY ENCLOSURES |
| IEC 60529 | EN 60529 | Degrees of protection provided by enclosures (IP Code) |
| IEC 61000 | EN 61000 | ELECTROMAGNETIC COMPATIBILITY (EMC) |
| Part 3: Limits | ||
| IEC 61000-3-2 | EN 61000-3-2 | Part 3-2: Limits for harmonic current emission (equipment input current <= 16 A per phase) |
| IEC 61000-3-3 | EN 61000-3-3 | Part 3-3: Limitation of voltage changes, voltage fluctuations flicker in public low voltage supply systems, for equipment with rated current <= 16 A per phase and not subjected to conditional connection |
| Part 4: Testing and measurement techniques | ||
| IEC 61000-4-2 | EN 61000-4-2 | Part 4-2: Electrostatic discharge immunity test |
| IEC 61000-4-3 | EN 61000-4-3 | Part 4-3: Radiated radio frequency, electromagnetic field immunity |
| IEC 61000-4-4 | EN 61000-4-4 | Part 4-4: Electrical fast transient/burst |
| IEC 61000-4-5 | EN 61000-4-5 | Part 4-5: Surge immunity test |
| IEC 61000-4-6 | EN 61000-4-6 | Part 4-6: Immunity to conducted disturbances, induced by radio-frequency fields |
| IEC 61000-4-8 | EN 61000-4-8 | Part 4-8: Power frequency magnetic field immunity test |
| IEC 61000-4-9 | EN 61000-4-9 | Part 4-9: Pulse magnetic field immunity test |
| IEC 61000-4-10 | EN 61000-4-10 | Part 4-10: Damped oscillator magnetic field immunity test |
| IEC 61000-4-11 | EN 61000-4-11 | Part 4-11: Voltage dips, short interruptions and voltage variation immunity tests |
| Part 6: Generic standards | ||
| IEC 61000-6-3 | EN 61000-6-3 | Part 6-3: Generic standards -Emission standard for residential commercial and light industrial environments |
| IEC 61000-6-4 | EN 61000-6-4 | Part 6-4: Generic standards -Emission standard for industrial environment |
OY Elspecta-AB's Cross Reference of MIL-STD vs. IEC Standards* - Issue March 26, 2022
OY Elspecta-AB:n MIL-STD vs. IEC -standardien ristiviittaus* - Numero 26.3.2022
